Skylight Shades

Skylight Shades in Zionsville, IN

Tensioned channels and a power plan, settled before ordering

Call (317) 863-9966Get Free Quote
Quick Answer

Answers here cover the whole lifecycle: measuring, ordering, fabrication, installation, care and service. A custom window covering is a long-term purchase and the later stages deserve as much attention as the first.

  • Service: Skylight Shades for Zionsville homeowners
  • Service area: Zionsville, IN and surrounding areas
    • How soon depends on which job it is. A new custom order waits on fabrication, typically two to five weeks after the measure. A repair like a restring or a cord lock doesn't wait on anything.
  • Insured and bonded
  • Serving Zionsville, IN since 2008
Skylight Shades Services

Expert Skylight Shades for Zionsville Homes

Overhead glass in Zionsville is mostly a two story problem, and Stonegate is the clearest case. Only 24 of its 378 houses are single story, the typical house runs 5,243 square feet, and the build ran 2004 through 2018, straight through the years when a skylight over a stair or a rear great room was ordinary specification. Holliday Farms carries the current version instead, with clerestory bands set above the main glass on houses that start at $1 million. Either way you end up with the same job: a fabric panel working on a sloped or flat plane, well above head height, where a pole isn't a serious answer.

Two things make this different from every other shade in the house. Gravity won't hold fabric flat against a slope, so the panel has to run in tensioned side channels down both edges, and those channels get fitted to a curb that can be out of square even on a house framed in 2010. Then there's power. A skylight shade is motorized because there's no honest manual option up there, and Hunter Douglas states PowerView battery life is about one year. Getting a charge cable or a low voltage feed to a ceiling that high is a decision you want made before the order, not discovered on install day.

When to Call

Signs You Need Skylight Shades

If you notice any of these in your Zionsville home, it is worth booking a measure. None of it is urgent, and none of it fixes itself either.

The room under the vault runs hot all July

You want the winter sun without the July version

A tube unit has nothing on it and no obvious option

An older shade sags away from the sloped glass

Flooring below the skylight has lightened in a stripe

Glare lands on a screen you can't move

A skylight bakes the room every afternoon

The shade quit halfway down and stayed there

The bottom rail hangs away from a shallow slope

A new build left every skylight bare

Our Process

How Zionsville Window Treatments Handles Skylight Shades

Every job follows the same five-step process. Transparent, thorough, and done right the first time.

1

In-home measure booked

2

Channels set, motor paired

3

Travel limits set and re-checked

4

Solar panel exposure checked

5

Hembar weight set for the pitch

Real Project Photos

Skylight Shades in Zionsville

Photographs from real skylight shades jobs completed by our crew in Zionsville and surrounding areas.

Custom shades measured and installed in ZionsvillePlantation shutters fitted to a Zionsville windowCellular shades in a Zionsville living room
Scope of Work

What Skylight Shades Includes

Every Zionsville job is documented item by item. Here is what the crew covers.

Every unit measured at the glass frame itself, since the finished shaft below it is usually wider and often flared outward

Slope of the glass recorded, because a shade on a pitched plane has to be held against gravity rather than hung from a rail

Tensioned side channels specified on anything that isn't vertical, so the fabric can't belly away from the glass in the middle

Reach assessed out loud at the measure: what a pole can work, what needs a ladder, what nobody should be climbing to at all

Power method settled before the fabric is chosen, because a dead battery over a stairwell is a different problem than one at eye level

Rechargeable wands, trickle charge points and solar charging panels priced into the job rather than mentioned afterward

Battery interval written next to the height of the opening, since Hunter Douglas puts PowerView life at about one year

Low-voltage locations marked for a licensed electrical contractor wherever a hardwired motor is the sane answer

Fabric picked for what the opening actually does wrong, whether that's July glare on a screen or a bedroom lit at sunrise

Cellular fabric considered where the opening bleeds heat in January, with clearance held off the cold glass above it

Shape templated on site for a trapezoid, a triangle or any angled unit that isn't a plain rectangle

Channel finish and fabric color judged from the floor, since the underside is the only face of this shade you will ever see

Radio path tested from where you'll stand to where the motor will sit, because a deep shaft and foil-faced insulation both cut range

Travel limits set top and bottom, then re-checked on a return visit once the fabric has relaxed

A written plan for how the unit comes down again for service, cleaning or a battery change

Debris sitting in the light well pointed out before install, since a shade hides that and doesn't remove it

Written contract with scope, dates and total price, as IC 24-5-11 requires on residential work over $150

Every unit run full travel from the floor with the remote in your hand before the ladder leaves the room

Pricing

What Skylight Shades Cost in Zionsville

Published national ranges put custom-fabricated shades at roughly $250 to $2,600 a window and motorized window coverings at roughly $300 to $1,500 per window installed. Those are national category figures, not a quote for an address in Zionsville. Overhead units sit high in both bands and there are honest reasons why. The fabric runs inside tensioned side channels instead of hanging free. The shape is frequently not a rectangle, so somebody builds a template. Almost every unit is motorized, because nobody wants a pole in the family room, and the motor then needs a charging plan that a wall outlet six feet away would have solved. Access is the last multiplier: the install happens off a ladder or a lift. Zionsville Window Treatments prices these from the measured frame in Boone County, with the power method decided before the number is written.

By Product

How Skylight Shades Differ by Product

Every product in this trade behaves differently in a room. Here is what that means for this work.

Tensioned side channel track: Aluminum channels fixed to each side of the frame with the fabric held under tension between them. On sloped or horizontal glass this isn't a light-blocking upgrade, it's the thing that stops the fabric from sagging away from the glass.

Cellular skylight fabric: A honeycomb fabric on an overhead track, which is what people specify when the opening is losing heat in the coldest weeks. DOE and ORNL measured up to 20 percent heating energy savings for cellular shades against a bare window.

Solar screen fabric overhead: An open weave rated by openness factor, sized to cut glare while you can still tell it's daylight up there. It's the right call over a kitchen or a stairwell where the complaint is brightness rather than heat or privacy.

Room darkening skylight fabric: An opaque face inside channels, which is as dark as an overhead opening gets. The channels close the side light, and the honest limit is the head and hem, where a small amount still finds its way around the fabric.

Rechargeable battery wand: A wand of cells that slides out of the headrail for charging. On a reachable unit that's a twenty minute job once a year. On an unreachable one, plan the charging point at the order stage rather than discovering it later.

Solar charging panel: A small panel mounted where it actually sees sky, wired to trickle charge the battery wand. Over glass that gets real sun this is the arrangement that keeps a hard-to-reach unit running without anybody hauling a ladder around.

Hardwired low-voltage motor: Power run to the header by a licensed electrical contractor, with our low-voltage locations marked for them. It costs the most up front and it's the only version that never needs a battery, which on high glass is worth arguing about.

Pole-operated manual unit: A track shade worked with a telescoping pole and a hook. It's inexpensive, it never needs power, and it's only pleasant on an opening you can actually reach from the floor with a pole you don't mind storing.

Templated specialty shape: A trapezoid, a triangle or an angled unit built from a physical template taken at your glass. Nothing about these is stock, and the template is why the finished shade follows the frame instead of leaving a wedge of daylight at one corner.

Remote, repeater and scene control: The control layer that makes an overhead shade usable: a handheld or wall remote, a repeater where the signal has to cross a header, and scenes so a bank of skylights moves together instead of one at a time.

Light Control

See What Each Fabric Does To The Light

Pick a fabric below and the window updates. It's a drawing rather than a photograph, so read it as a rough guide to what each family does in a Zionsville room, and to what it doesn't do.

Fabric type

Sheer, 10 percent openness

Ten percent of the weave is open, so you keep the view and most of the daylight. Glare drops a little. After dark, once your lamps are on, someone outside can read shapes through it, which is why this belongs on a view window rather than a bedroom.

Openness factor is printed on the fabric card, so you can compare one line against another before you order anything.

Keeps the viewNot private after dark

Solar, 5 percent openness

The usual pick for a west window or a covered porch. You can still read the yard through it, glare comes down noticeably, and the fabric intercepts a good share of the sun before it reaches you at four in the afternoon.

It also cuts the UV landing on floors and furniture. NFRC puts UV at roughly 40 to 60 percent of fading damage, so this slows fading rather than stopping it.

View and glare controlSlows fading

Solar, 3 percent openness

A tighter weave. The room goes dimmer and the view drops back to an outline. Choose it where the sun is the problem and the view is second, which around here usually means a west wall in July. That's a common call on this side of Indianapolis.

Openness affects how much you see out, not how private you are. A 3 percent fabric still shows silhouettes at night.

View becomes an outlineStrong glare control

Solar, 1 percent openness

Close to a solid fabric with a little view left in it. This is the strongest glare control in the solar family.

The trade is that it darkens the room on a gray January day too. Indianapolis averages a January high near 36F and the light is flat, so think about how the room reads in both seasons before you commit.

Darkest solar optionDim on gray days

Light filtering

No view through it. Daylight comes through the face diffused, so the room stays bright without a hot spot across the television or the kitchen island. This is the default for living spaces.

It isn't private in reverse at night. With the lamps on and the sun down, silhouettes still show.

No view through itBright without the glare

Room darkening

A denser fabric, usually with a liner behind it. Most of the light coming through the face is gone.

Light still arrives around the edges on an inside mount, so a room darkening shade gives you a dim room rather than a dark one. If someone in the house sleeps during the day, say so at the measure and we'll scope it differently.

Dim, not darkEdges stay bright

Blackout

The fabric itself passes essentially no light. What you'll still see is the perimeter. Lutron publishes an inside-mount light gap of about 3/4 inch per side on its Roller 20 and 64 shades, along with a standard factory deduction of 1/16 inch per side, and shades over 120 inches tall or past a 4:1 height-to-width ratio get larger gaps than that.

So if you need a genuinely dark bedroom, that gap has to be dealt with on purpose, either with side channels or by going outside mount. We tell you which one your opening can carry while we're still standing in the room.

Dark facePerimeter needs a plan

Openness factor is a measured fabric spec, so you can compare it line to line. The category names are not measured. One maker's room darkening can behave like another maker's light filtering, which is why the sample books come to the measure and get opened in the room they're going in, at the hour that room has the problem.

Common Questions

Skylight Shades FAQ

Questions we hear most often from Zionsville homeowners considering skylight shades.

In almost every case, yes, and it's worth saying why rather than treating it as an upsell. A skylight sits above reach, so the alternatives are a long crank pole or a cord loop hanging down into the room. The pole is awkward on a sloped plane and gets used twice. A hanging loop over a stair landing is the exact configuration nobody wants in a house with children. Motorization removes both. On a Stonegate stairwell skylight, where the ceiling is running two full stories, there's really no other sensible way to operate the shade.
The fabric runs inside a channel on each side of the opening and stays under tension the whole travel, which is what keeps it flat instead of sagging away from the glass. The channel also closes off most of the edge gap, so a room darkening fabric actually performs like one. The catch is fit. Channels are rigid and the curb they mount to may not be square, which is why we measure the opening at the head and again at the sill before ordering, rather than assuming the framing is true. On a Stonegate house framed anywhere between 2004 and 2018, that check takes two minutes and saves a return trip.
You plan the feed before the shade is ordered. Three arrangements are realistic. A rechargeable battery wand that comes down periodically, which is fine on a low hallway skylight and miserable over a two story great room. A trickle charge line run to the curb, which needs a path. Or a low voltage supply, which is the right answer during a remodel while the ceiling is open. Electrical work goes to an electrical contractor and we coordinate around it. On a finished ceiling in a Colony Woods house from the early 1980s, the honest answer is sometimes that only the wand is practical.
It slows the damage rather than preventing it. NFRC attributes roughly 40 to 60 percent of fading to ultraviolet, so a screen fabric that cuts UV meaningfully reduces one big share of the problem while visible light and heat keep doing their part. Overhead glass is the worst case for this because the sun hits it near perpendicular in summer, which is exactly when a Zionsville July averages a high of 85.2F. A room darkening skylight shade closed through the middle of the day does more for a hardwood floor than any coating on the glass will.
It changes it quite a bit. A bathroom skylight sits directly above rising steam, and Zionsville's muggy season runs about 25 May to 22 September, so the fabric spends four months of the year in humid air. Woven fabrics and anything with a laminated blackout backing hold that moisture against themselves and eventually spot along the hem. We specify a moisture tolerant screen or a solid vinyl faced fabric instead and accept slightly less darkness. The side channels stay weep clear so water that does condense has somewhere to go instead of sitting in the track.
We find out at the measure instead of at the install. A skylight curb is framed on site and it moves with the house, and 24.3 percent of Zionsville's housing predates 1980, so out of square is common in the older stock and not unheard of in the newer. We take three widths and three heights, then both diagonals. If the deviation is more than the channel can absorb, the options are an outside mounted panel that covers the whole curb, or a custom channel set that follows the actual opening. Either costs more than the catalog number, and you hear that number before you commit.
Four things stack up. The fabric runs in tensioned side channels rather than hanging off a headrail, so there's more hardware in the product. The opening is often a trapezoid or a triangle, which means a template and a one-off build. Almost every unit gets a motor, since a pole is only charming for about a week. Then there's access, because installing above a two story room is ladder work rather than step-stool work. Nationally, custom shades run about $250 to $2,600 and motorization adds roughly $300 to $1,500 per window installed.
Tension. On a vertical window gravity does the work and the hembar hangs straight. Tip that plane over and the same fabric wants to hang away from the glass in the middle, which looks wrong and lets light run around the edges. So an overhead unit rides in aluminum channels down each side, with the fabric held taut between them. Get the channels parallel and the fabric tracks correctly. Get them out of parallel by a sixteenth and the shade fights you at one end, which is why the frame gets measured rather than the finished opening below it.
Somebody gets a ladder, which is exactly why we settle the power method before the fabric. Hunter Douglas states that PowerView battery life is about one year, and that number is the single most under-disclosed cost on a motorized job at any height. Overhead it turns into an access problem as well as a cost. The answers are a rechargeable wand you can reach, a solar panel that trickle charges it, or hardwired power run to the header. We price those honestly at the quote so the yearly reality is in front of you.
Usually yes, and it's the version we push on genuinely unreachable glass. A low-voltage supply comes to the header and the motor never needs a battery again. The electrical work belongs to a licensed electrical contractor, and we mark our low-voltage locations for them so the wire lands where the motor actually is. It costs more at the start and it costs nothing every spring after that. On a shade that needs a lift to service, that math stops being close.
Close, if you buy the right build. An opaque fabric running inside side channels closes off the side light, which on overhead glass is where most of it wants to come in. What we won't tell you is that it will be perfect, because there's still a head and a hem where a thin line can show. Compare that to an ordinary inside mounted shade on a wall window: Lutron publishes 3/4 inch per side of light gap on their Roller 20 and 64 product, and channels are how you close that. Overhead, channels aren't optional anyway.
It helps with the two things you can feel. Overhead glass takes sun for more hours than any wall window in the house, and in a Zionsville July, with average highs at 85.2F, a bare skylight is a fixed heat source over a room you can't rearrange. A screen or an opaque fabric cuts the direct beam and takes the glare down. On the heating side, cellular fabric is the one with documented testing behind it, where DOE and ORNL measured up to 20 percent heating energy savings against a bare window. We won't turn any of that into a dollar figure for you.
Worth planning for rather than ignoring. In January, when average lows around Boone County sit near 20.9F, overhead glass runs cold and the air in the shaft is warmer and wetter than you'd guess. A shade held tight against that glass creates a still pocket where moisture can collect. We keep clearance between the fabric and the glass, we don't seal the shaft, and in a bath or a kitchen with a skylight we talk about running the shade open part of the day through the coldest weeks.
At the glass frame, never at the finished opening you see from the room. Most shafts are wider than the glass and many are flared, so a shade measured at the ceiling line would be badly oversized and would have nowhere to mount. We measure the frame in both directions, record the slope, check the diagonal, and note where every screw can actually land. On an angled unit that measure becomes a template instead of a set of numbers.
Usually, with a template. Fixed angled and triangular units get built to a physical pattern taken at the glass, and they either operate along one axis or stay fixed as a permanent filter, depending on the geometry. A trapezoid with two parallel sides is the friendliest shape and often operates normally. A true triangle frequently ends up as a fixed panel, which is a real answer rather than a failure, and it's better than an oversized rectangle leaving a lit wedge in the corner.
Gently, and less often than you'd think. Vacuum the face on low with a brush head when you can reach it, and leave the channels alone unless something is actually binding in them. The dust and insect debris that collects in a light well is worth clearing before we install, because a shade covers it up rather than dealing with it, and you won't want to revisit that decision later. If the unit is above a stairwell, ask us how it comes down before you need it to.
Yes, on any opening you can reach comfortably with a pole. A pole-operated track shade costs a fraction of a motorized unit, it never needs power, and it works fine in a room with an eight or nine foot ceiling where the pole lives in a closet nearby. Above a two story space it stops being reasonable, because the pole gets long and unwieldy, and most people quit using it by the second season. That's the honest dividing line we use.
We test it at the measure rather than after the install. Radio range gets cut by masonry, by metal in the framing and by foil-faced insulation, and a skylight sits behind more of that than a window does because the signal has to get up through a shaft and past a header. Where it's marginal, a repeater goes in on the same floor and the problem disappears. Where a house has several overhead units, a hub placed for signal rather than for whichever shelf is closest to the router usually settles it.
It ages faster, yes, and it's the same reason you wanted a shade. Overhead glass takes more hours of direct sun than anything else in a Zionsville house, so the fabric on that unit is working harder than the one in your living room. Solar screen weaves and vinyl-faced fabrics hold up best. On the room side, NFRC attributes roughly 40 to 60 percent of fading damage to UV, so the shade slows what happens to your floors and furniture below it. It reduces that. It doesn't end it.
Two to five weeks is the normal custom fabrication window, and overhead units sit toward the longer end because the channels, the motor and any templated shape all get built to your specific frame. Nothing there is a delay. It's a factory making a one-off. You get the fabrication window in writing next to the scope, the dates and the total price, which the Indiana Home Improvement Contract Act requires on residential work over $150. If a factory date moves, you hear it from us in the week we hear it.
Areas We Serve

Skylight Shades Across Zionsville

We measure and install in every one of these Zionsville neighborhoods. Each has its own page with the build eras, window conditions and mounting notes for that section.

Related Services

Other Window Treatment Services in Zionsville

Zionsville Window Treatments handles the full scope of window treatment work. Explore our other services below.

Faux Wood Blinds in Zionsville

The right slat for rooms that swing humid

Learn more →

Wood Blinds in Zionsville

Real basswood, and only in rooms that stay conditioned

Learn more →

Vertical Blinds in Zionsville

Sized by track width, drawn away from your door

Learn more →
Free In-Home Measure

Schedule Your Free In-Home Measure in Zionsville

Contact Information

Reach Us Directly

Our team prioritizes scheduled measures and service calls, and books in-home measures during business hours.

Office
1417 Commerce Avenue, Indianapolis, IN 46201
Hours
Mon-Fri 8a-6p
Service Area
Zionsville, IN and Surrounding Areas

Ready to Book Your Measure?

Call us to set up an in-home measure, or to ask about a treatment that has stopped working. We will talk it through on the phone first.

Call (317) 863-9966
Service area

Serving Zionsville and the surrounding area

Call NowGet Quote